Tutorials for both Little Red Riding Hood and The Big Bad Wolf below.

Need a last minute costume, but don't want to spend $50 on a cheapo from the costume store?
Red Riding Hood: $1.50, 20 minutes.
Wolf: $8, 1.5 hours. (only $2 if you have a nightgown already)
How to:
LITTLE RED RIDING HOOD

I bought a $1 yard of red fabric from Wal-mart and thought I could just drape it over my head. It looked all wrong so I searched the internet for how to make a cloak. I found cute ideas like this one from Martha Stewart and these too, but I didn't want to sew! I didn't want to spend any time at all! Fortunately, I learned at least one thing from these...It needs to be a semi-circle, not a square. Don't even worry about cutting a hood pattern and sewing!!
Materials:
- 1 yard red fabric
- 1.5 yards red ribbon
-
Stapler
-
Black paper
-
Basket
-
Old belt
-
Tea towel
-
T-shirt
-
Any color skirt
Step 1 (cut cloak): Cut a semi-circle

Step 2 (wear cloak):
Hang straight edge over head, tie 1 yard of ribbon around your neck (save .5 yard for later), then pull out volume from the top for a hood. (Your done with the cloak in only 5 mins!)


Step 3 (apron): Put on a t-shirt and skirt and tuck a t-towel into the skirt to look like an apron (see first photo)
Step 4 (belt/corset): Take a piece of black cardstock and cut in the shape shown below, then poke 8 holes (4 on each side) down the center for lacing.

Step 5: Lace the red ribbon like tying a shoe, then put on an old black belt (or black ribbon tied around you) and staple the paper corsette on the front! No one could even tell it was paper the whole night!
You could use hot glue instead of staples, and it might be more sturdy.

Your done! Just put on some tights and shoes and do your hair however. I used a basket as my purse. You could just wrap all your belongings in another tea-towel so they aren't all visible. Have fun!
How to:
THE BIG BAD WOLF

Materials:
Step 1: (Snout)
Get a paper cup (ask for an extra at the coffee shop in the morning) Cut out the bottom and cut up the sides so that one half is about 1/3 (the lower snout) of the cup and the other is about 2/3 (the upper snout) of the cup. Cut a little more of an angle pointing to the bottom so its more triangular. (see second photo below)
Step 2:
Cut jagged edges on the sides of both the upper and lower snout. Then on the larger (upper) snout tape a ball of black tape around the end for the nose

Step 3:
Tape the inside of the mouth black, then tape the two pieces together at the top (jaw). (Now they are connected, but flexy so that you can bite on the lower jaw with your teeth to make it open and shut. Bend the teeth toward the inside of the mouth


Step 4: Using the cup parts, trace a pattern on the back of the fur and cut the fur out using an exacto knife (if you use scissors the fur will look funny and you'll have fur everywhere.) The just staple the fur on top and bottom of the snout. Strap a rubber band around the jaw so you can put it around the head, and your done!
Step 5: (Ears)
Cut 2 triangles (with x-acto knife) with the fur direction going toward the top of the triangle. Then just fold them in half at the bottom and bobby pin them in the hair (secured with curlers on either side) or pin to a night cap.
Step 6: Arms (or legs)
My wolfs granny nightgown had really short arms for him, so we put fur on the arms. You could also do the legs and then put on granny slippers. Measure around the arm and mark. Then cut out the piece in a slightly belled shape (more room to move hands around), staple (or hand stitch for a more secure hold) the ends together and slip over arm stuffing ends into the sleeve.
Step 7: (Tail)
Just clip the short end of your fabric and rip a long piece of fur (ripping won't cut any hairs so it wont get all over, so it's much better than cutting and easier than exacto knife). Then fold the piece and staple, then pin to your wolf's nightgown by the bum.
You're all done! Just put the pieces on, and maybe a little grey make-up if you want.
Recent Comments